- #My meade autostar controller stopped working how to#
- #My meade autostar controller stopped working serial#
- #My meade autostar controller stopped working Pc#
- #My meade autostar controller stopped working windows#
On Meade LX-200 and LX-400 telescopes, the RS-232 port is located on the mount base. On most telescopes, the RS-232 port is a 4- or 6-wire modular (“telephone”) jack.
#My meade autostar controller stopped working serial#
Contact your telescope manufacturer to obtain the correct serial cable for your telescope.Ĭonnect your telescope serial cable to the RS-232 port on your telescope. Different telescopes require different serial cables.
#My meade autostar controller stopped working Pc#
With serial telescopes, you'll need a serial cable to connect your telescope's RS-232 port to a standard PC DB9 Male serial port. With iOptron telescopes, the USB “B” port is on the GOTONova hand controller. On Meade LS telescopes, the USB “B” port is on the mount base. With USB telescopes, use a standard USB cable to connect SkyFi's USB “A” port to the telescope's USB “B” port. Browse to again to confirm your new network settings. Wait a few seconds for SkyFi's network to reset, then re-join SkyFi's new wireless network. Click the "Save Changes" button when finished.
![my meade autostar controller stopped working my meade autostar controller stopped working](https://www.meadeuk.com/img/astronomy/Meade/accessories/handboxes/AutoStar_III/Meade_AutoStar_III_35-4700-13LF-01-1000x1000.jpg)
Your WEP key must contain exactly 10 or 26 hexadecimal characters (digits 0-9, letters A-F). You should see a web page which lets you set SkyFi's network name (SSID), enable WEP security, and enter a WEP key.
![my meade autostar controller stopped working my meade autostar controller stopped working](https://www.cloudynights.com/uploads/monthly_09_2020/post-341750-0-64178900-1599672622.jpg)
Launch a web browser, like Safari or Internet Explorer. To configure SkyFi's wireless network after you have joined it: If you don't, other SkyFi units with the same network name may conflict with yours, and other users may be able to connect with (and control!) your hardware. However, we strongly recommend that you change SkyFi's wireless network name and enable WEP security before using SkyFi in the field. You can skip to the next section if you just want to start controlling your telescope.
#My meade autostar controller stopped working how to#
For information on how to do this, go to our web site, at the URL listed at the top of this page. This way, your iPhone, computer, and SkyFi can all be on your home network at the same time, and your computer or iPhone can connect to the internet while simultaneously connected to SkyFi. SkyFi can be configured to join an "Infrastructure" wireless network, such as generated by a typical home router. If several devices are joined to SkyFi's network, that network will still exist even if SkyFi itself is turned off! To completely shut down SkyFi's wireless network, make sure all devices have disconnected from SkyFi's network - and wait a minute or two for your computer to "forget" the network. only to other devices on SkyFi's network.
#My meade autostar controller stopped working windows#
Consult macOS or Windows Help for more information on how to check your network settings. This is the default setting on most computers. For this to work correctly, make sure your computer or mobile device is configured to use DHCP (Dynamic Host Configuration Protocol). When you join SkyFi's network, SkyFi will automatically assign an IP address to your computer or other wireless device. Join this network from your PC, Mac, iPhone, iPod, or other wireless device - just as you would join any other WiFi network. When you turn SkyFi on, it creates an open wireless network named "SkyFi". Please note: batteries are not included, and AC adapters are available separately. SkyFi's electronics can function properly at temperatures up to 80° C! This is normal SkyFi doesn't use any more power than the 6V supplied by the internal battery pack, and it is simply dissipating the extra power as heat. When running SkyFi from an external power source, it may become quite warm. See the Troubleshooting section below if the status LED still does not turn green. If it does not, turn the power off for a few seconds, then turn it on again. The status LED should light up red at first, then turn green after a few seconds.
![my meade autostar controller stopped working my meade autostar controller stopped working](https://astro-gadget.net/wp-content/uploads/2018/12/AutoBt-1.jpg)
Move the power switch right to the BAT position to use battery power, or left to the EXT position to use external power. A car battery with an auto cigarette lighter adapter should work fine SkyFi's DC input jack accepts any standard center-positive 5.5 mm OD x 2.1 mm ID male barrel plug. The input DC power requirements are 6 - 12 Volts, 0.5 - 1.5 Amps. If you have an external power adapter, plug it into SkyFi's DC input jack. Battery life should be 8 to 10 hours for alkaline batteries under normal operating conditions. To power SkyFi internally, insert four AA batteries into the battery compartment. You can power SkyFi from four AA batteries, or from an external DC power source. These instructions assume that you are familiar with your own telescope equipment, and with basic home-networking concepts like SSIDs, WEP security, and IP addresses. This quick start guide is only an introduction, and more recent information may be available here: This page contains the Quick Start Guide for our SkyFi wireless telescope controller.